Gas to induction.
Moving off gas usually needs a new circuit from the switchboard to the cooktop. A licensed gasfitter caps the gas; we handle the electrical side.
INDUCTION COOKTOP INSTALLATION / CROYDON / 3136 Induction cooktops.
Properly connected.
Ready to cook.
Gas to induction, or a straight swap.
The circuit and switchboard checked first.
01 / GAS TO INDUCTION, DONE PROPERLY
Induction Cooktop Installation
in Croydon.
We install induction cooktops in Croydon 3136, from gas-to-induction changes to straight swaps, checking the circuit and switchboard first. We explain the options and agree the work before anything starts.
Induction cooktops heat the pan directly, so they are quick, easy to clean and need no gas. Most draw more power than an older electric cooktop, so the circuit, cable and switchboard need checking before the new one goes in.
Voltra Electrical installs induction cooktops across Melbourne, from straight swaps to gas-to-induction changes. We check your chosen model against the existing supply and explain any new circuit or switchboard work before we start.
Plan your induction cooktopElectric to induction.
An existing electric cooktop circuit may or may not suit the new model. We compare its rating and cable with the cooktop's requirements.
A kitchen renovation.
Send the cooktop model early so the circuit, isolating switch and benchtop cut-out can be planned with your cabinet maker.
02 / THE WORK, CONSIDERED
More power than it looks.
Planned from the board.
CONSIDERED / FROM START TO FINISH
Model. Circuit. Switchboard.
Checked together.
Most induction cooktops need more than 15 amps, so many need their own circuit back to the switchboard. Some models can be set to draw less power to suit a smaller circuit; we check what yours allows.
A new cooktop circuit is protected by a safety switch (RCD) at the switchboard, and the cooktop gets its own isolating switch near the bench. If the board has no room, we explain the options before quoting.
Plan your induction cooktopGAS TO INDUCTION
Switching from gas?
What changes.
Many Melbourne kitchens are moving their cooking off gas. This is what the change usually involves on the electrical side.
- A new circuit
- A gas cooktop usually has only a power point nearby for its ignition, which is too small for most induction cooktops. We run a dedicated circuit from the switchboard.
- Safety switch protection
- Under the Australian wiring rules (AS/NZS 3000), a new cooktop circuit is protected by a 30 mA safety switch (RCD) at the switchboard.
- An isolating switch
- A hard-wired cooktop needs its own switch near the bench, where you can see and reach it, not on the cooktop itself.
- The gas side
- A licensed gasfitter disconnects and caps the old cooktop's gas supply. We coordinate timing so you are not without a cooktop for long.
- Switchboard check
- If the board is full or has older protection, we explain what needs to change before the cooktop goes in.
- Testing & certificate
- We test the circuit and the cooktop connection and provide a Certificate of Electrical Safety for the electrical work.
Replacing the oven at the same time? We can plan both circuits in one visit.
03 / KNOW YOUR SETUP
Before you buy.
Check these first.
The model number is the best starting point. Send it before you order and we can check what your kitchen needs.
- Circuit & cable
- We compare the cooktop's rating with the existing circuit and cable. A larger cooktop often needs a new, dedicated circuit.
- Switchboard space
- A new circuit needs space and a safety switch at the board. Older boards may need changes first, which we explain before quoting.
- Single or three phase
- Most homes run an induction cooktop on single-phase power. Three-phase is rarely needed for a cooktop alone.
- Cut-out & clearances
- The benchtop cut-out and clearances come from the installation instructions. A nominal width alone does not confirm the fit.
- Pots & pans
- Induction only works with magnetic cookware. If a magnet sticks firmly to the base of a pan, it should work.
- Gas disconnection
- A licensed gasfitter must cap the gas. We work around their timing so the cooktop is connected when the bench is ready.
04 / FROM FIRST LOOK TO FINAL CHECK
Clear at every step.
- 01
Send the model.
Tell us the cooktop model, your suburb and whether you are replacing gas, electric or starting fresh.
- 02
Check the supply.
We check the circuit, cable and switchboard against the model, then confirm the work and price in writing.
- 03
Coordinate the trades.
We line up with your gasfitter and cabinet maker so the circuit is ready when the bench is.
- 04
Connect, test and certify.
We connect the cooktop, test the circuit and safety switch, and provide a Certificate of Electrical Safety.
05 / BEFORE WE GET STARTED
Good questions.
Clear answers.
Do you provide induction cooktop installation in Croydon?
Yes. We cover every part of Croydon (VIC 3136). Send your street, the work you need and any access notes, and we will confirm availability and the next step. We also cover Croydon Hills and Croydon North.
Can I switch to an induction cooktop in my Croydon home?
Usually, yes. Induction cooktops often need a dedicated circuit of a higher rating than an older electric cooktop. We check the circuit, cable and switchboard against the model you have chosen.
What affects the cost of induction cooktop installation in Croydon?
Mainly access (roof space, subfloor and wall construction), the existing circuits and whether the switchboard has room for the work. 83% of Croydon homes are separate houses, where roof and subfloor access usually make cable runs simpler. We confirm the scope before quoting.
Can you disconnect the gas cooktop?
We handle the electrical work. A licensed gasfitter must disconnect and cap the gas, and we can work around their timing.
Do I need new pots and pans?
Only if they are not magnetic. Induction heats magnetic cookware, so if a fridge magnet sticks firmly to the base, the pan should work.
Can you install a cooktop I have already bought?
Yes, as long as it suits the space and the supply. Send the model number and installation instructions so we can check the circuit and cut-out first.
What helps you quote?
The cooktop model, a photo of the kitchen and a photo of the switchboard with its cover closed. You do not need to move appliances or open anything.
YOUR HOME / YOUR AREA
Croydon.
A clearer next step.
Croydon had about 28,610 residents and about 12,080 homes at the 2021 Census, with a median age of 39. In Croydon's older homes, moving from gas to induction often needs a new or larger circuit, and sometimes switchboard changes. The share of homes that are separate houses is 83% in Croydon, lower than in next-door Croydon Hills (100%) and Croydon North (95%).
From Lalor, Croydon is roughly 28 km to the south-east, in Melbourne's outer east, around Main Street and Croydon station. Croydon sits within the Maroondah council area. We also work in neighbouring Croydon Hills, Croydon North, Croydon South and Ringwood.
Figures: ABS 2021 Census of Population and Housing.
Explore our full induction cooktop installation guide, or other electrical services available for your property in Croydon.
Also serving nearby areas
INDUCTION COOKTOP INSTALLATION / LET’S GET STARTED
Your kitchen.
Ready for induction.
Tell us about the cooktop and the kitchen it is going into. A model number helps us get started.
Induction cooktop installation
No electrical specifications needed from memory. Share the model if you have it; we assess the supply and connection.
0495 096 344We use these details to respond to your enquiry. Privacy policy.
INDUCTION COOKTOP INSTALLATION